常用模具专业英语
模具英语专业术语
一、浇口：gate
浇口位位置：gate location
浇口形式：gate type
侧浇口口：side gate
点浇口： pin-point gate
浇口大小：gate size
二次浇口：switching runner/gate
注嘴口径：sprue diameter
二、流道: runner
热流道：hot runner,hot manifold
热嘴冷流道: hot sprue/cold runner
唧嘴直流: direct sprue gate
圆形流道：round(full/half runner
流道电脑分析：mold flow analysis
流道平衡:runner balance
热嘴：hot sprue
热流道板：hot manifold
发热管：cartridge heater
探针: thermocouples
插头：connector plug
插座： connector socket
密封/封料： seal
三、水路：water line
水管头（公）：line lpug
水管头（母）：tube
塑胶管：plastic tube
快速接头：jiffy quick connector plug/socker
四、模具零件：mold components
三板模：3-plate mold
二板模：2-plate mold
导柱：leader pin/guide pin
导套：bushing/guide bushing
导套：shoulder guide bushing
导柱：guide pin
顶针板：ejector retainner plate
顶板：support plate
螺丝： screw
管钉：dowel pin
开模槽：ply bar scot
模仁精定位：core/cavity inter-lock
顶针：ejector pin
顶管：ejector sleeve
顶管针：ejector pin
推板：stripper plate
尼龙开闭器：nylon latch lock
斜顶：lifter
模胚（架）： mold base
上内模：cavity insert
下内模：core insert
滑块： slide
镶件：insert
耐磨板/油板：wedge wear plate
滑块压块：plate
支撑柱: support pillar
注嘴： sprue bushing
挡板：stop plate
定位圈：locating ring
锁扣：latch
模板精定位：parting lock set
推杆：push bar
紧固螺丝：S.H.S.B
分流锥：spure sperader
料把导套:bush
垃圾钉：stop pin
水隔片：buffle
弹簧柱：spring rod
弹簧:die spring
顶出导套：ejector guide bush
顶出导柱：ejector guide pin
镶针：pin
销子：dowel pin
弹弓：ball catch
喉塞: pipe plug
锁模块：lock plate
斜顶：angle from pin
斜顶杆：angle ejector rod
尼龙拉勾：parting locks
活动臂：lever arm
提前复位杆：early return bar
气阀：valves
斜导柱：angle pin
五、术语：terms
承压平面平衡：parting surface support balance
分模面排气：parting line venting
复位杆与母模干涉：return pin and cavity interference
模具总厚度超出成型机规格：mold base shut hight
顶针水冷却：water line interferes withejector pin
料位出上/下模：part from cavith (core) side
模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.
不准用镶件： Do not use (core/cavity) insert
用铍铜做镶件： use beryllium copper insert
初步（正式）模图设计：preliinary (final) mold design
倒沟：reverse core
弹弓压缩量：spring compressed length
稳定性好：good stability,stable
强度不够：insufficient rigidity
均匀冷却：even cooling
扣模：sticking
热膨胀：thero expansion
公差：tolorance
电极：copper electrode
